Inspector - Manufacturing Processes

Job Description:

Description:IAM Hourly represented employees who currently work at the main (Sunnyvale/Palo Alto) unit, Santa Cruz, VAFB or Eastern Range facilities must apply to open requisitions on Brass Ring to be considered for the position.

Perform all inspection tasks relative to the acceptance or rejection for process or workmanship of in-process or completed electronics parts, circuit card assemblies, cable harness assemblies, polymerics, solar array parts, solar array assemblies, mechanical satellite assemblies, and equipment. Inspection of processing of parts, assemblies, and materials for conformance to engineering drawings, specifications, and engineering data.

Working from blueprints, schematics, inspection criteria and other manufacturing and other manufacturing, engineering, and test documentation inspect at process steps or at the completion of all work.

Inspect a variety of electronics parts, electrical and mechanical assemblies and equipment such as printed circuit boards, surface mount assemblies, flex circuitry, solar assemblies/arrays, mechanical satellite subassemblies, flight hardware subassemblies and top assemblies, vehicle harnesses and ground support cables and ground support equipment for workmanship and manufacturing process conformity, verification of test setups.

Visually review and compare with acceptable standards such processes and assembly operations as registration, plating, mechanical operations, soldering, brazing, welding, swaging, wire wrap, lugging, splicing, routing, encapsulation, torquing and final assembly as related to mechanical subassemblies and electrical and electronics hardware. Support hardware test setup and troubleshooting per test processes.

Verify manufacturing processes and test activities are properly performed as documented in Manufacturing Processes Standards per the embedded Operations Verification Instructions. Witness or perform manual hi-pot and continuity operations on wiring. Inspect the incorporation of design changes as required.

Inspect parts, assemblies, and materials for the results or effect of such processes or operations as anodizing, painting, chromodizing, etching, passivating, dichromating, pickling, plating, degreasing, rust preventing, sandblasting, etc., for conformance to blueprints, specifications, and other engineering data.

Check or examine solutions and equipment used for processing to determine chemical, mechanical or electrical conformance with applicable specifications. Generate non-conformance documentation for hardware when requirements are not met.

Stamp or otherwise approve acceptable items, reject unacceptable items and prepare all necessary documentation. Verify completion of Material Review Board (MRB) actions using nonconformance system. Use information processing equipment as required to perform the above tasks. Assist quality engineers and managers in processing product, manufacturing, and test documentation as required to facilitate acceptance of hardware products.

Ability to obtain and maintain DOD security clearance

Typical start time for this position is 5:00am.
Basic Qualifications:
• Satisfactory performance as an Inspector, Electronics Manufacturing Processes - Trainee and demonstrated understanding of area systems, process, and quality policies, Experience inspecting electronics and mechanical assemblies.

• Knowledge of finish and processing methods and standards; metals and materials worked with; chemistry as applied to finishing and processing.

• Ability to use precision measuring instruments; use shop mathematics; read and interpret engineering drawings, specifications, and engineering data.
Desired Skills:
If you possess these key skills, you will be able adapt to this role more quickly:

• Technical aptitude or experience in one or more of the following areas: fabrication or quality assurance of electronic CCA/PWB solder, Box/Module, Cable Harness or Acceptance Testing Prior experience with wire harness or electronics manufacturing

• Solder, bond, and coating certification

• Industry-related certifications such as NASA Hand Solder, J-STD, Hardware torque, Adhesive Bonding, Polymerics, Connector Mate & De-Mate, and NASA cable harness

• Capable of Multi-tasking in a fast-paced team environment

• Computer skills – Microsoft office

• SAP/ERP working knowledge

• Ability to work a flexible work week including flexible start time (typically 5:00AM start time),weekends, and overtime as needed

• Ability to lift and move 40 lbs unassisted
• Ability to climb scaffolding and ladders as required to make required inspections

• Normal or corrected vision is required. Applicant shall be able to pass visual acuity examination

• Strong interpersonal communication skills

• Manufacturing and/or testing experience – especially in product acceptance and non-
conformance documentation
Security Clearance Statement: This position requires a government security clearance, you must be a US Citizen for consideration.
Clearance Level: Secret
Other Important Information You Should Know
Expression of Interest: By applying to this job, you are expressing interest in this position and could be considered for other career opportunities where similar skills and requirements have been identified as a match. Should this match be identified you may be contacted for this and future openings.
Ability to Work Remotely: Onsite Full-time: The work associated with this position will be performed onsite at a designated Lockheed Martin facility.
Work Schedules: Lockheed Martin supports a variety of alternate work schedules that provide additional flexibility to our employees. Schedules range from standard 40 hours over a five day work week while others may be condensed. These condensed schedules provide employees with additional time away from the office and are in addition to our Paid Time off benefits.
Schedule for this Position: 4x10 hour day, 3 days off per week

The base range for this position in California is $25.10 - $43.26.
Benefits offered: Medical, Dental, Vision, Life Insurance, Short-Term Disability, Long-Term Disability, 401(k) match, Flexible Spending Accounts, EAP, Education Assistance, Parental Leave, Paid time off, and Holidays. The wage range and benefits summary is a general guideline and is governed by the applicable collective bargaining agreement when extending an offer.
Lockheed Martin is an Equal Opportunity/Affirmative Action Employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, pregnancy, sexual orientation, gender identity, national origin, age, protected veteran status, or disability status.
The application window will close in 90 days; applicants are encouraged to apply within 5 - 30 days of the requisition posting date in order to receive optimal consideration.
At Lockheed Martin, we use our passion for purposeful innovation to help keep people safe and solve the worlds most complex challenges. Our people are some of the greatest minds in the industry and truly make Lockheed Martin a great place to work.

With our employees as our priority, we provide diverse career opportunities designed to propel, develop, and boost agility. Our flexible schedules, competitive pay, and comprehensive benefits enable our employees to live a healthy, fulfilling life at and outside of work. We place an emphasis on empowering our employees by fostering an inclusive environment built upon integrity and corporate responsibility.

If this sounds like a culture you connect with, you’re invited to apply for this role. Or, if you are unsure whether your experience aligns with the requirements of this position, we encourage you to search on Lockheed Martin Jobs, and apply for roles that align with your qualifications.
Experience Level: Hourly/Non-Exempt
Business Unit: SPACE
Relocation Available: No
Career Area: QA/Test and Inspection
Type: Full-Time
Shift: First

If you possess these key skills, you will be able adapt to this role more quickly:

• Technical aptitude or experience in one or more of the following areas: fabrication or quality assurance of electronic CCA/PWB solder, Box/Module, Cable Harness or Acceptance Testing Prior experience with wire harness or electronics manufacturing

• Solder, bond, and coating certification

• Industry-related certifications such as NASA Hand Solder, J-STD, Hardware torque, Adhesive Bonding, Polymerics, Connector Mate & De-Mate, and NASA cable harness

• Capable of Multi-tasking in a fast-paced team environment

• Computer skills – Microsoft office

• SAP/ERP working knowledge

• Ability to work a flexible work week including flexible start time (typically 5:00AM start time),weekends, and overtime as needed

• Ability to lift and move 40 lbs unassisted
• Ability to climb scaffolding and ladders as required to make required inspections

• Normal or corrected vision is required. Applicant shall be able to pass visual acuity examination

• Strong interpersonal communication skills

• Manufacturing and/or testing experience – especially in product acceptance and non-
conformance documentation

Job Ident #: 69517838336

Company Details

Lockheed Martin

6801 Rockledge Dr
Bethesda, Maryland 20817 USA
www.lockheedmartinjobs.com/

Lockheed Martin Corporation is an American global aerospace, defense, security and advanced technologies company with worldwide interests. It was formed by the merger of Lockheed Corporation with Martin Marietta in March 1995. It is headquartered in North...

Benefits:
TBD

(Job and company information not to be copied, shared, scraped, or otherwise disseminated/distributed without explicit consent of JSfirm, LLC)

Job Info

Location

Sunnyvale, California, United States

Type

Permanent

Company Details

Lockheed Martin

6801 Rockledge Dr
Bethesda, Maryland 20817 USA
www.lockheedmartinjobs.com/